单词查询
dowels
美['daʊəl]，英['daʊəl]，
释义
「
」
n. 暗销；【木工】榫钉；夹缝钉；【建】传力杆； v. 用合板钉钉合；用(暗)销接合；在…设置传力杆； 网络释义： 销子；木钉；合销；
例句
He said he figured the rainwater had settled in the pinholes, where wooden dowels held the joints together.
他说，估计是雨水渗进了木钉孔里，而正是这些木榫钉使它们结合在一起的。
The armourer harvests wood to make either slat armour composed of numerous wooden slats sewn together or rod-armour made of wooden dowels .
工匠们砍伐木材，或用诸多木板拼成板甲，或用诸多木条钉成栅甲。
Dowels must not be used to withstand side thrust force (keys are to withstand this force and will be specified when quoting).
当承受侧力时不能使用合销（健用来承受这种压力，在报价时应说明）。Q。
Once your dowels are cut to size, spread a thin layer of glue in all the dowel holes and along the edges of the mating boards.
做好圆榫后，在要对接的两边和榫孔内都涂上薄薄一层胶水。
Because the last two require some fairly specialized equipment, dowels are the best choice for the beginner.
因为后两种都需要一些特殊装备才能搞定，所以圆木榫就成了新手的首选。
3-Using small dowels helps with edge joint alignment. Bore the dowel holes with a dowelling jig and an electric drill.
图3。用圆木榫来协助对齐接口。用电钻和圆榫开孔模具来打圆榫孔。
Recommendations for the position and size of the holes for these dowels can be found in the table.
这些暗销孔的建议位置和大小可以在表8中找到。
Next hand up the auxiliary-bowstring to the outside of copper- dowels .
I quickly fashioned a ladder out of wooden dowels and nylon rope.
Dimples are cast into the housing feet to identify the drilling location for the dowels.
轴承座上铸有凹印，表示为定位销钻孔的位置。
他说，估计是雨水渗进了木钉孔里，而正是这些木榫钉使它们结合在一起的。
The armourer harvests wood to make either slat armour composed of numerous wooden slats sewn together or rod-armour made of wooden dowels .
工匠们砍伐木材，或用诸多木板拼成板甲，或用诸多木条钉成栅甲。
Dowels must not be used to withstand side thrust force (keys are to withstand this force and will be specified when quoting).
当承受侧力时不能使用合销（健用来承受这种压力，在报价时应说明）。Q。
Once your dowels are cut to size, spread a thin layer of glue in all the dowel holes and along the edges of the mating boards.
做好圆榫后，在要对接的两边和榫孔内都涂上薄薄一层胶水。
Because the last two require some fairly specialized equipment, dowels are the best choice for the beginner.
因为后两种都需要一些特殊装备才能搞定，所以圆木榫就成了新手的首选。
3-Using small dowels helps with edge joint alignment. Bore the dowel holes with a dowelling jig and an electric drill.
图3。用圆木榫来协助对齐接口。用电钻和圆榫开孔模具来打圆榫孔。
Recommendations for the position and size of the holes for these dowels can be found in the table.
这些暗销孔的建议位置和大小可以在表8中找到。
Next hand up the auxiliary-bowstring to the outside of copper- dowels .
I quickly fashioned a ladder out of wooden dowels and nylon rope.
Dimples are cast into the housing feet to identify the drilling location for the dowels.
轴承座上铸有凹印，表示为定位销钻孔的位置。