单词查询
gusset
美['ɡʌsət]，英['ɡʌsɪt]，
释义
「
」
v. 在…缝三角形布料；给…装上角撑板； n. （缝在衣服上用以放大、加固等的）衬料； 网络释义： 角板；三角形插布；连接板；
例句
They write the name on their gusset and keep it for a week.
The puny pendency face of Tang Lu Er, but the hand tightly grasp his gusset not to put, the tears presently dripped out.
“哦……”唐芦儿微垂下脸，手却紧紧抓着他的衣袖不放，眼泪快要掉出来了。
Cent of aluminous gusset plate has punching and plane for the surface two kinds.
Upon welding all four beads, the last exposed gusset end is bent to match the contour of the upper support bow.
焊接后所有四个球，最后暴露折端弯曲的轮廓匹配的弓上的支持。
This hole is placed 16. 3 inches behind the front tip of the main gusset as shown.
这个洞是放置所示16.3英寸主要扣板落后于前面的一角。
For the 90 degree Cross-member Trike Design, the Gusset is extended by an inch as shown.
对于90度交叉成员三轮车的设计，该折是延长1英寸的显示。
If you seek advice the word that aluminous gusset plate is famous brand, with intermediate for, be 0. 6 millimeter mostly.
假如你咨询的铝扣板是名牌的话，以中档来说，大多都是0.6毫米的。
It established the relation between apex angle and tucking angle of gusset of extrusion line for blown-film through geometrical deduction.
通过几何推导，确立了吹膜机组插板顶角与插板插入角之间的关系。
Remember that the main gusset is slightly shortened to accommodate the cross-member gusset.
记住，主要扣板略有缩短，以满足跨成员扣板。
Weld the main gusset as shown in the drawing above.
The puny pendency face of Tang Lu Er, but the hand tightly grasp his gusset not to put, the tears presently dripped out.
“哦……”唐芦儿微垂下脸，手却紧紧抓着他的衣袖不放，眼泪快要掉出来了。
Cent of aluminous gusset plate has punching and plane for the surface two kinds.
Upon welding all four beads, the last exposed gusset end is bent to match the contour of the upper support bow.
焊接后所有四个球，最后暴露折端弯曲的轮廓匹配的弓上的支持。
This hole is placed 16. 3 inches behind the front tip of the main gusset as shown.
这个洞是放置所示16.3英寸主要扣板落后于前面的一角。
For the 90 degree Cross-member Trike Design, the Gusset is extended by an inch as shown.
对于90度交叉成员三轮车的设计，该折是延长1英寸的显示。
If you seek advice the word that aluminous gusset plate is famous brand, with intermediate for, be 0. 6 millimeter mostly.
假如你咨询的铝扣板是名牌的话，以中档来说，大多都是0.6毫米的。
It established the relation between apex angle and tucking angle of gusset of extrusion line for blown-film through geometrical deduction.
通过几何推导，确立了吹膜机组插板顶角与插板插入角之间的关系。
Remember that the main gusset is slightly shortened to accommodate the cross-member gusset.
记住，主要扣板略有缩短，以满足跨成员扣板。
Weld the main gusset as shown in the drawing above.